What does Duty, Dwell, Pulse & Converge mean?

[Annie Andrey]

Just another more simple explanation per kind favour of TrueRife and the Lord alone knows who else contributed?
@nnie
__________________________________________________ _______


Q: I cannot grasp terms like pulse, converge, sweep, duty, etc. Could you explain?

A:

Pulse:

Frequencies are pulsed by not only Rife Researchers but by almost all researchers using frequencies to target or destroy microorganisms. Pulses Vs straight runs on frequencies have been demonstrated to get better die offs and kills. Pulsing is basically and OFF / ON command.

To understand pulse, picture someone's fist applying 10lbs constant pressure to your jaw, vs the fist pulsing up and down while making contact with your jaw with the same amount of pressure. The pulsing motion will obviously result in damage, while constant pressure is easily adjusted to resulting in less or no damage at all.


CONVERGE OR SWEEP:

Convergences and sweeps generate a shotgun effect.
The purpose of convergences or sweeps is to pick up mutations or fluctuations of the targeted pathogens that may be slightly off target. Some strains for example may have a MOR or resonant frequency of 440 Hz, while others of the same classification or family may be resonating at 439.734 Hz or 441.78 Hz. While 440 Hz is believed by many researchers to be close enough for a kill, when dealing with harmonics, 440 Hz may miss the targeted pathogen entirely, while the fractional frequencies around the primary frequency may be a perfect hit.


DUTY

Duty is the off and on cycle of the square wave. Duties of 71.5 or 78 Hz will generally pick up all the harmonics of the frequencies up toe scale, while a duty of 50% will only pick up half the harmonics.


Harmonics are a doubling of the frequency up the scale:
10 Hz, 20 Hz, 40 Hz, 80 Hz, 160 Hz etc. The targeted pathogen may be oscillating at 160 Hz. If we are running 40 Hz with a duty of 71.5 we will still pick up the 160 Hz harmonic which is the true target frequency in this example.


Instructions for F-series generators:

Pulse:

To set the frequencies to pulse, you must type the word pulse followed by two numbers.

Example Pulse 1 50

The first number is the amount of pulses for each cycle the frequency runs. In this case it will pulse once during a complete cycle.

The second number is the “duty cycle.” This is the amount of time for each pulse the frequency is ON. In this example the frequency is ON 50% of the time and OFF 50%. To turn off the pulse for another set of frequencies you must type: Pulse 00

Sweeps:

To sweep from one frequency to another either up or down you must type the word SWEEP followed by 3 Numbers.
Example: Sweep 100 350 1

The first number is the start number for the sweep to begin, the second is the stop number. The third number is the HZ that the sweep will use to reach its final destination. In this case the sweep will take place in 1 Hz increments beginning with 100 then 101 then 102 then 103 all the way up till it reaches 350Hz.

Hint: to create fast sweeps type in dwell .5 before the sweep commands. This means that only one half second will pass between sweeps from one number to the next. If you do not type in a dwell time the sweep will not move to the next number in sequence for 3 minutes.

Converge:

This converge command consist of two numbers. Its purpose is to converge at frequencies above and below the primary number until it reaches that frequency.

Example: Converge 10 1

The first number is the number of Hz above and below the primary number that the convergence will begin. The second number is the amount of Hz that the convergence will change within the command. If the example above is being used, and the frequency is 100, the first frequency would be 110, followed by 90, followed by 109, followed by 91, followed by 108, followed by 92…etc, till you finally converge on 100 to finish that set.

To turn the convergence off for another set of frequencies to follow you must type: Converge 0 0

Truerife